MirOS Manual: ndp(8)

NDP(8)                   BSD System Manager's Manual                    NDP(8)

NAME

     ndp - control/diagnose IPv6 Neighbor Discovery Protocol (NDP)

SYNOPSIS

     ndp [-nt] hostname
     ndp [-nt] -a | -c | -p
     ndp [-nt] -r
     ndp [-nt] -H | -P | -R
     ndp [-nt] -A wait
     ndp [-nt] -d hostname
     ndp [-nt] -f filename
     ndp [-nt] -i interface [flags ...]
     ndp [-nt] -I [interface | delete]
     ndp [-nt] -s nodename etheraddr [temp] [proxy]

DESCRIPTION

     The ndp command manipulates the address mapping table used by the Neigh-
     bor Discovery Protocol (NDP).

     -A wait
             Repeat -a (dump NDP entries) every wait seconds.

     -a      Dump the currently existing NDP entries. The following informa-
             tion will be printed:

             Neighbor    IPv6 address of the neighbor.

             Linklayer Address
                         Linklayer address of the neighbor. It could be
                         "(incomplete)" when the address is not available.

             Netif       Network interface associated with the neighbor cache
                         entry.

             Expire      The time until expiry of the entry. The entry could
                         become "permanent", in which case it will never ex-
                         pire.

             S           State of the neighbor cache entry, as a single
                         letter:

                         N       Nostate
                         W       Waitdelete
                         I       Incomplete
                         R       Reachable
                         S       Stale
                         D       Delay
                         P       Probe
                         ?       Unknown state (should never happen).

             Flags       Flags on the neighbor cache entry, in a single
                         letter. They are: Router, proxy neighbor advertise-
                         ment ("p"). The field could be followed by a decimal
                         number, which means the number of NS probes the node
                         has sent during the current state.

     -c      Erase all the NDP entries.

     -d      Delete specified NDP entry.

     -f      Parse the file specified by filename.

     -H      Harmonize consistency between the routing table and the default
             router list; install the top entry of the list into the kernel
             routing table.

     -I      Shows the default interface used as the default route when there
             is no default router.

     -I interface
             Specifies the default interface to be used when there is no in-
             terface specified even though required.

     -I delete
             The current default interface will be deleted from the kernel.

     -i interface [flags ...]
             View ND information for the specified interface. If additional
             arguments flags are given, ndp sets or clears the specified flags
             for the interface. Each flag should be separated by whitespace or
             tab characters. Possible flags are as follows. All of the flags
             can begin with the special character '-', which means the flag
             should be cleared. Note that you need -- before -foo in this
             case.

             nud     Turn on or off NUD (Neighbor Unreachability Detection) on
                     the interface. NUD is usually turned on by default.

             accept_rtadv
                     Specify whether or not to accept Router Advertisement
                     messages received on the interface. Note that the kernel
                     does not accept Router Advertisement messages unless the
                     net.inet6.ip6.accept_rtadv variable is non-0, even if the
                     flag is on. This flag is set to 1 by default. See
                     sysctl(8) and sysctl.conf(5) for further details on how
                     to set the net.inet6.ip6.accept_rtadv variable.

     -n      Do not try to resolve numeric addresses to hostnames.

     -P      Flush all the entries in the prefix list.

     -p      Show prefix list.

     -R      Flush all the entries in the default router list.

     -r      Show default router list.

     -s      Register a NDP entry for a node. The entry will be permanent un-
             less the word temp is given in the command. If the word proxy is
             given, this system will act as a proxy NDP server, responding to
             requests for hostname even though the host address is not its
             own.

     -t      Print timestamp on each entry, making it possible to merge output
             with tcpdump(8). Most useful when used with -A.

RETURN VALUES

     The ndp command exits with 0 on success, and non-zero on errors.

SEE ALSO

     ip6(4), sysctl.conf(5), arp(8), sysctl(8), tcpdump(8)

HISTORY

     The ndp command first appeared in the WIDE Hydrangea IPv6 protocol stack
     kit.

MirOS BSD #10-current            May 17, 1998                                1

Generated on 2014-07-04 21:17:45 by $MirOS: src/scripts/roff2htm,v 1.79 2014/02/10 00:36:11 tg Exp $

These manual pages and other documentation are copyrighted by their respective writers; their source is available at our CVSweb, AnonCVS, and other mirrors. The rest is Copyright © 2002‒2014 The MirOS Project, Germany.
This product includes material provided by Thorsten Glaser.

This manual page’s HTML representation is supposed to be valid XHTML/1.1; if not, please send a bug report – diffs preferred.