TOKENINIT(8) BSD System Manager's Manual TOKENINIT(8)
activinit, cryptoinit, snkinit - modify or add user in ActivCard, CRYPTO- Card, or SNK-004 authentication system
tokeninit [-f] [-h] [-m mode] [-s] [-v] user_ID [...]
The tokeninit utility may also be invoked by one of the following names: activinit, cryptoinit, or snkinit. Depending on the name it was invoked as, it will initialize the system information to allow one to use the Ac- tivCard, CRYPTOCard, or SNK-004 digital encryption token to login. The tokeninit utility is intended for use by the system administrator. Token card systems provide strong user authentication by combining a user's unique knowledge (a Personal Identification Number) and a physical object (the token) which the user must have in their possession to login. The system administrator programs the token with a secret encryption key which is also stored in the database. The user programs the token with a PIN. To discourage exhaustive attempts to guess the PIN, configuration options permit the token to be programmed to erase knowledge of the shared secret should the user enter an excessive number of incorrect PIN entries. The user activates the token by entering their PIN into the token. After activating the token, the user enters a random number challenge presented by the host computer into the token. The challenge is encrypted by the token and a response is displayed. The user then enters the response at the host computer's prompt, where it is compared with the anticipated response. Token cards typically support multiple unique encryption keys. This fa- cility allows a single token to be used for multiple computer systems, or multiple user instances on the same system. The options are as follows: -f Force reinitialization of an existing account. The current shared secret stored in the database will be replaced with a new shared secret. The new shared secret must be entered into the token, re- placing the current one. -h Read the shared secret as a 16 digit hexadecimal integer rather than a sequence of 8 octets. This is not supported when invoked as snkinit. -m Specify the input modes allowed for this user. Possible modes are decimal (dec), hexadecimal (hex), phonebook (phone), and reduced-input (rim). Not all modes are available for all types of cards. Multiple -m options may be specified to enable multiple modes. By default only the hexadecimal mode is enabled, except for the SNK-004 token, which by default only enables the decimal mode. If an attempt is made to initialize a card with only reduced-input, the default mode for the card is silently includ- ed. -s By default, tokeninit prompts for a shared secret to enter into the authentication database. The -s option generates a 64-bit cryptographically strong key for use in the token. This shared secret will be saved in the database for the user ID specified on the command line. After entering the shared secret into the to- ken, determine that the checksum computed by the token matches the one displayed by tokeninit. -v Enable verbose mode. tokeninit will emit messages on the status of each user ID processed. REDUCED-INPUT MODE Reduced-input mode allows the token to predict the next challenge, given the current challenge. This may be used to eliminate the need to enter the challenge to the token or may also be used with a paper list. Using a program such as x99token(1) many challenges could be precomputed and printed. This list should be kept secret. This list can then take the place of an actual token until the system has issued all the challenges printed. Challenges are predicted by the following algorithm: * Encrypt the last challenge with the shared secret key * AND each byte of the response with 0x0f * Modulo each byte by 10 (0x0a) * ADD 0x30 (ASCII value of '0') to each byte The resulting 8 bytes are all ASCII decimal digits and are the next chal- lenge.
/etc/activ.db database of information for ActivCard system /etc/crypto.db database of information for CRYPTOCard system /etc/snk.db database of information for SNK-004 system
Diagnostic messages are logged via syslog(3) with the LOG_AUTH facility.
A supplier for ActivCard tokens may be obtained by contacting: ActivCard, Inc. 303 Twin Dolphin Dr., Ste 420 Redwood City, CA 94065 Tel: (415) 654-1700 Fax: (415) 654-1701 CRYPTOCard tokens may be obtained by contacting: CRYPTOCard Incorporated Attn: Wade Clark 1649 Barclay Blvd. Buffalo Grove, Illinois 60089 Tel: (800) 307-7042 / (708) 459-6500 Fax: (708) 459-6599 <email@example.com> SNK-004 tokens are no longer available for purchase.
x99token(1), syslog(3), login_token(8), tokenadm(8)
Jack Flory <firstname.lastname@example.org>
Not all modes of all cards are supported. MirOS BSD #10-current September 26, 1995 1
Generated on 2015-04-13 10:26:13 by $MirOS: src/scripts/roff2htm,v 1.80 2015/01/02 13:54:19 tg Exp $
These manual pages and other documentation are copyrighted by their respective writers;
their source is available at our CVSweb,
AnonCVS, and other mirrors. The rest is Copyright © 2002–2015 The MirOS Project, Germany.
This product includes material provided by Thorsten Glaser.
This manual page’s HTML representation is supposed to be valid XHTML/1.1; if not, please send a bug report – diffs preferred.