MirOS Manual: wacom(4)


WACOM(4)            UNIX Programmer's Manual             WACOM(4)

NAME

     wacom - Wacom input driver

SYNOPSIS

     Section "InputDevice"
       Identifier "idevname"
       Driver "wacom"
       Option "Device"   "devpath"
       ...
     EndSection

DESCRIPTION

     wacom is an XFree86 input driver for Wacom devices.

     The wacom driver functions as a pointer input device, and
     may be used as the X server's core pointer.

SUPPORTED HARDWARE

     This driver supports the Wacom IV and Wacom V protocols.
     Preliminary support is available for USB devices on some
     Linux platforms.

CONFIGURATION DETAILS

     Please refer to XF86Config(5) for general configuration
     details and for options that can be used with all input
     drivers.  This section only covers configuration details
     specific to this driver.

     Multiple instances of the Wacom devices can cohabit. It can
     be useful to define multiple devices with different active
     zones. Each device supports the following entries:

             Option "Type" "stylus"|"eraser"|"cursor"
                 sets the type of tool the device represent. This
                 option is mandatory.

             Option "Device" "path"
                 sets the path to the special file which
                 represents serial line where the tablet is
                 plugged.  You have to specify it for each sub-
                 section with the same value if you want to have
                 multiple devices with the same tablet. This
                 option is mandatory.

             Option "USB" "on"
                 tells the driver to dialog with the tablet the
                 USB way.  This option is only available on some
                 Linux platforms.

             Option "DeviceName" "name"
                 sets the name of the X device.

XFree86                   Version 4.5.0                         1

WACOM(4)            UNIX Programmer's Manual             WACOM(4)

             Option "Suppress" "Inumber"
                 sets the position increment under which not to
                 transmit coordinates. This entry must be speci-
                 fied only in the first Wacom subsection if you
                 have multiple devices for one tablet. If you
                 don't specify this entry, the default value is
                 computed to

             Option "Mode" "Relative"|"Absolute"
                 sets the mode of the device.

             Option "Tilt" "on"
                 enables tilt report if your tablet supports it
                 (ROM version 1.4 and above). If this is enabled,
                 multiple devices at the same time will not be
                 reported.

             Option "HistorySize" "number"
                 sets the motion history size. By default the
                 value is zero.

             Option "AlwaysCore" "on"
                 enables the sharing of the core pointer. When
                 this feature is enabled, the device will take
                 control of the core pointer (and thus will emit
                 core events) and at the same time will be able,
                 when asked so, to report extended events. You
                 can use the last available integer feedback to
                 control this feature. When the value of the
                 feedback is zero, the feature is disabled. The
                 feature is enabled for any other value.

             Option "TopX" "number"
                 X coordinate of the top corner of the active
                 zone.

             Option "TopY" "number"
                 Y coordinate of the top corner of the active
                 zone.

             Option "BottomX" "Inumber"
                 X coordinate of the bottom corner of the active
                 zone.

             Option "BottomY" "number"
                 Y coordinate of the bottom corner of the active
                 zone.

             Option "KeepShape" "on"
                 When this option is enabled, the active zone
                 begins according to TopX and TopY.  The bottom
                 corner is adjusted to keep the ratio

XFree86                   Version 4.5.0                         2

WACOM(4)            UNIX Programmer's Manual             WACOM(4)

                 width/height of the active zone the same as the
                 screen while maximizing the area described by
                 TopX, TopY, BottomX, BottomY.

             Option "DebugLevel" number
                 sets the level of debugging info reported.

             Option "BaudRate" "38400", "19200" or "9600"
                 changes the serial link speed. This option is
                 only available for wacom V models (Intuos).

             Option "Serial" "number"
                 sets the serial number associated with the phy-
                 sical device. This allows to have multiple dev-
                 ices of the same type (i.e. multiple pens). This
                 option is only available on wacom V devices
                 (Intuos). To see which serial number belongs to
                 a device, you have to set the DebugLevel to 6
                 and watch the output of the X server.

             Option "Threshold" "number"
                 sets the pressure threshold used to generate a
                 button 1 events of stylus devices for some
                 models of tablets (Intuos and Graphire).

SEE ALSO

     XFree86(1), XF86Config(5), xf86config(1), Xserver(1), X(7).

AUTHORS

     Frederic Lepied <lepied@xfree86.org>

XFree86                   Version 4.5.0                         3

Generated on 2014-07-04 21:17:45 by $MirOS: src/scripts/roff2htm,v 1.79 2014/02/10 00:36:11 tg Exp $

These manual pages and other documentation are copyrighted by their respective writers; their source is available at our CVSweb, AnonCVS, and other mirrors. The rest is Copyright © 2002‒2014 The MirOS Project, Germany.
This product includes material provided by Thorsten Glaser.

This manual page’s HTML representation is supposed to be valid XHTML/1.1; if not, please send a bug report – diffs preferred.