STRIP(4) BSD Programmer's Manual STRIP(4)
strip - packet-mode network device driver for the Metricom Ricochet radio
pseudo-device strip [count]
Configures count strip interfaces, named st0, st1, etc, into a kernel built from a config file containing the given entry. Each strip interface is a pseudo-device driver for the Metricom Ricochet radio, operating in peer-to-peer packet mode. The strip driver takes outbound network packets, encapsulates them using the Metricom "starmode" framing, and sends the packets out an RS-232 in- terface to a Metricom Ricochet radio. Packets arriving from the radio via the serial link are decapsulated and then passed up to the local host's networking stack. strip is an acronym for Starmode Radio IP. In many ways, the strip driver is very much like the sl SLIP pseudo- device driver. A strip device is attached to a tty line with slattach(8). Once attached, the interface is configured via ifconfig(8). The major difference between the sl(4) SLIP pseudo-device driver and the strip driver is that SLIP works only between two hosts over a dedicated point- to-point connection. In contrast, strip sends packets to a frequency- hopping radio, which can address packets to any peer Metricom radio rath- er than just to a single host at the other end of a point-to-point line. Thus, one strip pseudo-device is usually sufficient for any kernel. In other respects, a strip interface is rather like an Ethernet inter- face. Packets are individually addressed, and subsequent packets can be sent independently to different MAC addresses. However, the "Star-mode" framing and MAC addressing are not in any way compatible with Ethernet. Broadcast or multicast to more than one radio is not possible, due to the independent frequency-hopping operation of the radios. The interface flags IFF_POINTOPOINT and IFF_BROADCAST are not supported on strip inter- face. In other words, strip implements a multiple-access, non-broadcast device, accessed via an RS-232 serial line, using a proprietary packet framing scheme. This version strip driver maps IP addresses to Metricom radio addresses using statically configured entries in the normal routing table. These entries map IP addresses of peer radios to the MAC-level addresses. The exact syntax of this mapping and an example are discussed below. The In- ternet Assigned Numbers Authority (IANA) has allocated an ARP type code for use with STRIP. A future version of this driver will support arp(4) to obtain the IP address of reachable peer radios dynamically.
This version of the strip driver requires static pre-configuration of the mapping from IP addresses to radio MAC addresses. The route(8) command should be used to bind a peer STRIP host's radio IP address to the peer's link-level radio address. Radio addresses are encoded using the hex equivalent of the radio's decimal ASCII address. For example, the follow- ing route command will configure a routing entry to a radio with a MAC address of 1234-5678, and an IP address 10.11.12.13: route add -host 10.11.12.13 -link 1:2:3:4:5:6:7:8 Generalising from this example to other IP addresses and to other 8-digit MAC addresses should be clear.
The Metricom radios can auto-baud at speeds up to 38.4k baud. At higher speeds -- 57600 or 115200 -- the radio cannot autobaud. When running at high speeds, the radio's serial port should be manually configured to permanently run at the desired speed. Use a terminal emulator and the Hayes command ATS304=115200 to set the serial baudrate to the specified number (or 0 for autobaud). The command AT&w will then save the current radio state in non-volatile memory. Metricom radios can operate in either "modem-emulation" mode or in packet mode (Starmode). The strip driver automatically detects if the radio has fallen out of starmode, and resets it back into starmode, if the baud rate was set correctly by slattach(8).
arp(4), inet(4), route(8), slattach(8), slip(8)
strip was originally developed for the Linux kernel by Stuart Cheshire of Stanford's Operating Systems and Networking group, as part of Mary Baker's MosquitoNet http://mosquitonet.stanford.edu/mosquitonet.html pro- ject. This strip driver was ported to BSD by Jonathan Stone at Stanford's Distributed Systems Group and first distributed with NetBSD 1.2.
Currently is IP-only. Encapsulations for AppleTalk and ARP have been de- fined, but are not yet implemented in this driver. strip has not been widely tested on a variety of lower-level tty drivers. The detection and resetting of radios that crash out of Starmode does not always work in this version of the driver. One workaround is to kill the slattach(8) process, ifconfig the strip interface down, and then start a new slattach and rerun ifconfig. MirOS BSD #10-current August 9, 2009 1
Generated on 2013-10-31 22:57:03 by $MirOS: src/scripts/roff2htm,v 1.77 2013/01/01 20:49:09 tg Exp $
These manual pages and other documentation are copyrighted by their respective writers;
their source is available at our CVSweb,
AnonCVS, and other mirrors. The rest is Copyright © 2002‒2013 The MirOS Project, Germany.
This product includes material provided by Thorsten Glaser.
This manual page’s HTML representation is supposed to be valid XHTML/1.1; if not, please send a bug report – diffs preferred.