MirOS Manual: bad144(8)

BAD144(8)                BSD System Manager's Manual                 BAD144(8)

NAME

     bad144 - read/write DEC standard 144 bad sector information

SYNOPSIS

     bad144 [-c] [-n] [-v] disk [snum [bad ...]]
     bad144 -a [-c] [-n] [-v] disk [bad ...]

DESCRIPTION

     bad144 can be used to inspect the information stored on a disk that is
     used by the disk drivers to implement bad sector forwarding.

     The options are as follows:

     -a      The argument list consists of new bad sectors to be added to an
             existing list. The new sectors are sorted into the list, which
             must be in order. Replacement sectors are moved to accommodate
             the additions; the new replacement sectors are cleared.

     -c      Forces an attempt to copy the old sector to the replacement, and
             may be useful when replacing an unreliable sector.

     -n      Make no permanent changes. Useful for debugging. Implies -v.

     -v      The entire process is described as it happens in gory detail if
             -v (verbose) is given.

     The format of the information is specified by DEC standard 144, as fol-
     lows. The bad sector information is located in the first 5 even numbered
     sectors of the last track of the disk pack. There are five identical
     copies of the information, described by the dkbad structure.

     Replacement sectors are allocated starting with the first sector before
     the bad sector information and working backwards towards the beginning of
     the disk. A maximum of 126 bad sectors are supported. The position of the
     bad sector in the bad sector table determines the replacement sector to
     which it corresponds. The bad sectors must be listed in ascending order.

     The bad sector information and replacement sectors are conventionally
     only accessible through the "c" file system partition of disk.o. If that
     partition is used for a file system, the user is responsible for making
     sure that it does not overlap the bad sector information or any replace-
     ment sectors. Thus, one track plus 126 sectors must be reserved to allow
     use of all of the possible bad sector replacements.

     The bad sector structure is as follows:

     struct dkbad {
             long    bt_csn;          /* cartridge serial number */
             u_short bt_mbz;          /* unused; should be 0 */
             u_short bt_flag;         /* -1 => alignment cartridge */
             struct bt_bad {
                   u_short bt_cyl;    /* bad sector cylinder number */
                   u_short bt_trksec; /* track and sector number */
             } bt_bad[126];
     };

     Unused slots in the bt_bad array are filled with all bits set, a puta-
     tively illegal value.

     bad144 is invoked by giving a device name (e.g., "hk0", "hp1"). With no
     optional arguments it reads the first sector of the last track of the
     corresponding disk and prints out the bad sector information. It issues a
     warning if the bad sectors are out of order. bad144 may also be invoked
     with a serial number for the pack and a list of bad sectors. It will
     write the supplied information into all copies of the bad-sector file,
     replacing any previous information. Note, however, that bad144 does not
     arrange for the specified sectors to be marked bad in this case. This
     procedure should only be used to restore known bad sector information
     which was destroyed.

     It is no longer necessary to reboot to allow the kernel to reread the
     bad-sector table from the drive.

SEE ALSO

     badsect(8)

HISTORY

     The bad144 command appeared in 4.1BSD.

BUGS

     It should be possible to format disks on-line under UNIX.

     It should be possible to mark bad sectors on drives of all type.

     On an 11/750, the standard bootstrap drivers used to boot the system do
     not understand bad sectors, handle ECC errors, or the special SSE (skip
     sector) errors of RM80-type disks. This means that none of these errors
     can occur when reading the file /bsd to boot. Sectors 0-15 of the disk
     drive must also not have any of these errors.

     The drivers which write a system core image on disk after a crash do not
     handle errors; thus the crash dump area must be free of errors and bad
     sectors.

MirOS BSD #10-current            June 6, 1993                                1

Generated on 2014-07-04 21:17:45 by $MirOS: src/scripts/roff2htm,v 1.79 2014/02/10 00:36:11 tg Exp $

These manual pages and other documentation are copyrighted by their respective writers; their source is available at our CVSweb, AnonCVS, and other mirrors. The rest is Copyright © 2002‒2014 The MirOS Project, Germany.
This product includes material provided by Thorsten Glaser.

This manual page’s HTML representation is supposed to be valid XHTML/1.1; if not, please send a bug report – diffs preferred.