MirOS Manual: fpit(4)


FPIT(4)             UNIX Programmer's Manual              FPIT(4)

NAME

     fpit - Fujitsu Stylistic input driver

SYNOPSIS

     Section "InputDevice"
       Identifier "idevname"
       Driver "fpit"
       Option "Device"   "devpath"
       ...
     EndSection

DESCRIPTION

     fpit is an XFree86 input driver for Fujitsu Stylistic Tablet
     PCs.

     The fpit driver functions as a pointer input device, and may
     be used as the X server's core pointer.

SUPPORTED HARDWARE

     This driver supports the touchscreen of the Stylistic LT and
     (with special options) of the Stylistic 500, 1000 and 2300.

     Under Linux the Fujitsus serial port is not, by default,
     detected. Therefore the following must be added to one of
     your start-up scripts. (Either one of the X scripts, or to
     rc.local or similar).

     setserial /dev/ttyS3 autoconfig

     setserial /dev/ttyS3 IRQ 15 baud_base 115200

     This driver now supports Stylistic 3400 (and possibly other
     passive-pen systems) with a special "Passive" paramter. Try
     this serial configuration for the 3400:

     setserial /dev/ttyS3 autoconfig

     setserial /dev/ttyS3 uart 16450 irq 5

CONFIGURATION DETAILS

     Please refer to XF86Config(5x) for general configuration
     details and for options that can be used with all input
     drivers.  This section only covers configuration details
     specific to this driver.

     The device supports the following options:

             Option "MaximumXPosition" "number"
                 Sets the maximum X position, use this to

XFree86                   Version 4.5.0                         1

FPIT(4)             UNIX Programmer's Manual              FPIT(4)

                 callibrate your touchscreen's right hand edge.

             Option "MinimumXPosition" "number"
                 Sets the minimum X position, use this to calli-
                 brate your touchscreen's left hand edge.

             Option "MaximumYPosition" "number"

             Option "MinimumYPosition" "number"
                 Same as for X axis, but for Y axis.

             Option "InvertX"

             Option "InvertY"
                 Invert the specified axis.

             Option "SwapXY"
                 Swap the X and Y axis.

             Option "Rotate" "CW"
                 Option "Rotate" "CWW" Manipulate the invert and
                 swap options to match screen rotations.

             Option "DeviceName" "name"
                 Option "DeviceName" "name" sets the name of the
                 X device.

             Option "AlwaysCore" "on"
                 enables the sharing of the core pointer. When
                 this feature is enabled, the device will take
                 control of the core pointer (and thus will emit
                 core events) and at the same time will be able,
                 when asked so, to report extended events. You
                 can use the last available integer feedback to
                 control this feature. When the value of the
                 feedback is zero, the feature is disabled. The
                 feature is enabled for any other value.

             Option "DebugLevel" number
                 sets the level of debugging info reported.

             Option "BaudRate" "38400", "19200" or "9600"
                 changes the serial link speed.

             Option "Passive"
                 decodes the passive pen.

     Example, for Stylistic LT setup is:
     Section "InputDevice"
       Identifier "mouse0"
       Driver "fpit"
       Option "Device"   "/dev/ttyS3"

XFree86                   Version 4.5.0                         2

FPIT(4)             UNIX Programmer's Manual              FPIT(4)

     EndSection

     And for other Stylistic devices try:
     Section "InputDevice"
       Identifier "mouse0"
       Driver "fpit"
       Option "Device"   "/dev/ttyS3"
       Option "BaudRate" "19200"
       Option "MaximumXPosition" "6250"
       Option "MaximumYPosition" "4950"
       Option "MinimumXPosition" "130"
       Option "MinimumYPosition" "0"
       Option "InvertY"
     EndSection

     For Stylistic 3400:
     Section "InputDevice"
       Identifier "mouse0"
       Driver "fpit"
       Option "Device"   "/dev/ttyS3"
       Option "BaudRate" "9600"
       Option "MaximumXPosition" "4070"
       Option "MaximumYPosition" "4020"
       Option "MinimumXPosition" "0"
       Option "MinimumYPosition" "0"
       Option "Passive"
       Option "SendCoreEvents"
     EndSection

SEE ALSO

     XFree86(1), XF86Config(5), xf86config(1), Xserver(1), X(7).

AUTHORS

     Original FPIT port: Rob Tsuk <rob@tsuk.com> and John Apfel-
     baum <johnapf@linuxslate.com>

     X4 Port: Richard Miller-Smith <richard.miller-
     smith@philips.com>, based on Elographics code from: Patrick
     Lecoanet

     X4.2 Cleanup: Alan Cox

XFree86                   Version 4.5.0                         3

Generated on 2014-04-02 20:57:59 by $MirOS: src/scripts/roff2htm,v 1.79 2014/02/10 00:36:11 tg Exp $

These manual pages and other documentation are copyrighted by their respective writers; their source is available at our CVSweb, AnonCVS, and other mirrors. The rest is Copyright © 2002‒2014 The MirOS Project, Germany.
This product includes material provided by Thorsten Glaser.

This manual page’s HTML representation is supposed to be valid XHTML/1.1; if not, please send a bug report – diffs preferred.